IOP-241
24 Channel Digital Input/ Output
Type II PCMCIA Card
INTERFACE CARDS FOR PERSONAL COMPUTERS
OMEGA ENGINEERING, INC.
One Omega Drive
P.O. Box 4047
Tel: (203) 359-1660
Fax: (203) 359-7700
Toll free: 1-800-826-6342
Stamford, CT 06907-4047
E-mail: [email protected]
IOP-241 Users Manual
1
Declaration of Conformity
Manufacturer's Name:
Omega Engineering, Inc.
Manufacturer’s Address:
One Omega Drive
Stamford, CT 06907-0047
Application of Council Directive:
89/ 336/ EEC
Standards to which
Conformity is Declared:
* EN50081-2
(EN55022)
* EN50082-1
(IEC 801-2, IEC 801-3, & IEC 801-4)
Type of Equipment:
Equipment Class:
Product Name:
Information Technology Equipment
Commercial, Residential and Light Industrial
PCMCIA Card
Model Number :
IOP-241
IOP-241 Users Manual
3
OMEGAnet On-line Service:
Internet e-mail:
info@omega.com
Servicing North America:
USA:
ISO 9001 Certified
One Omega Drive, Box 4047
Stamford, CT 06907-0047
Tel: (203) 359-1660
E-mail: info@omega.com
FAX: (203) 359-7700
Canada:
976 Bergar
Laval (Quebec) H7L 5A1
Tel: (514) 856-6928
E-mail: info@omega.com
FAX: (514) 856-6886
For immediate technical or application assistance:
USA and Canada:
Sales Service: 1-800-826-6342 / 1-800-TC-OMEGASM
Customer Service: 1-800-622-2378/ 1-800-622-BESTSM
Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN SM
TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA
Mexico and Latin America: Tel: (001) 800-826-6342
En Espanol: (001) 203-359-7803
E-mail: espanol@omega.com
FAX: (001) 203-359-7807
Servicing Europe:
Benelux:
Postbus 8034, 1180 LA Amstelveen, The Netherlands
Tel: (31) 20 6418405
Toll Free in Benelux: 0800 0993344
E-mail: nl@omega.com
Czech Republic:
ul.Rude armady 1868, 733 01 Karvina-Hraniee
Tel: 42 (69) 6311899
Toll Free: 0800-1-66342
FAX: 42 (69) 6311114
E-mail: czech@omega.com
France:
9, rue Denis Papin, 78190 Trappes
Tel: (33) 130-621-400
Toll Free in France: 0800-4-06342
E-mail: france@omega.com
Germany/Austria:
Daimlerstrasse 26, D-75392 Deckenpfronn, Germany
Tel: 49 (07056) 3017
Toll Free in Germany: 0130 11 21 66
E-mail: germany@omega.com
IOP-241 Users Manual
4
United Kingdom:
ISO 9002 Certified
One Omega Drive, River Bend Technology Drive
Northbank, Irlam, Manchester
M44 5EX, England
Tel: 44 (161) 777-6611
FAX: 44 (161) 777-6622
Toll Free in England: 0800-488-488
E-mail: info@omega.co.uk
It is the policy of OMEGA to comply with all worldwide safety and EMC/ EMI regulations that apply.
OMEGA is constantly pursuing certification of it’s products to the European New Approach Directives.
OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct but OMEGA Engineering, Inc.
accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patient connected
applications.
IOP-241 Users Manual
5
Table of Contents
1. Introduction
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.2 System Configuration
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2. DOS / Windows 3.x Installation
2.1 IOP-241 Client Driver for DOS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.1.1 Client Driver Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.1.2 Command Line Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.1.3 Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.2.1 Enabler Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.2.2 Command Line Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2.3 Common Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2.3 After Completing Configuration
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
3. Windows 95/98® Installation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2 Resource Settings in Windows 95/ 98
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.2.1 Viewing Resource Settings with Device Manager . . . . . . . . . . . . . . . . . . . . . . . 20
3.3 Changing Resource Settings with Device Manager
. . . . . . . . . . . . . . . . 21
3.4 After Completing Configuration
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4. Theory of Operation
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.1 I/ O Port Description
4.2 Port C Interrupt Description
4.3 External Interrupt Description
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
5. Register Descriptions
5.1 Data Port A Control Register (Base + 0)
5.2 Data Port B Control Register (Base + 1)
5.3 Data Port C Control Register (Base + 2)
. . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
5.4 Port C Interrupt Enable Register (Base + 5)
5.5 Interrupt Mode Control Register (Base + 6)
. . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . 28
5.6 Interrupt Status Register (Read Only) (Base + 7)
. . . . . . . . . . . . . . . . . . . 28
5.7 Interrupt Acknowledge Register (Write Only) (Base + 7)
. . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
5.8 Summary of Interrupt Source Options
5.9 Summary of Input/ Output Options
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5.10 Programming Example
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
IOP-241 Users Manual
6
7. Optional Accessories
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
7.1 CP-1037 Cable Assembly
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
7.2 UIO-37 Screw Terminal Block
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
IOP-241 Users Manual
7
List of Figures and Tables
Figure 1-1. IOP-241 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 3-1. Windows 95/ 98 Resource Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 6-1. IOP-241 33-Pin Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 7-1. CP-1037 D37 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Figure 7-2. UIO-37 Screw Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Table 1-1. Client Driver versus Enabler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Table 5-1. IOP-241 Program Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 5-2. Data Port A Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 5-3. Data Port B Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 5-4. Data Port C Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 5-5. Port C Interrupt Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Table 5-6. Interrupt Mode Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 5-7. Interrupt Status Register (Read Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Table 5-8. Interrupt Status Register (Write Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
IOP-241 Users Manual
8
1. Introduction
The IOP-241 is a 24 channel digital input/ output card for systems equipped with PCMCIA
Type II and/ or Type III expansion sockets.
1.1
IOP-241 Features
PC Card Standard Specification 2.10 Compliant
24 TTL compatible digital I/ O channels (8 channels can be used as interrupt sources)
Channels individually programmable as either input or output
Active high sensitive, active low sensitive, low-to-high transistion or high-to-low
transition interrupt modes (external interrupt available)
1.2
System Configuration
The figure below illustrates a complete IOP-241 system. For users that do not wish to interface
to the IOP-241 0.8mm I/ O connector, an optional adapter cable (CP-1037) is available to
convert this connector into an industry standard D-37 connector. For applications requiring
discrete wiring hook-ups, an optional screw terminal block (UIO-37) is available to convert the
D-37 connector into 37 single screw terminal blocks. These optional accessories are described
in detail in Chapter 7.
D37
IOP-241
UIO-37
Hirose-32
CP-IO37
Figure 1-1. IOP-241 System Configuration
IOP-241 Users Manual
9
2. DOS / Windows 3.x Installation
Two configuration software programs are provided with the IOP-241: a Client Driver and a
card Enabler. Both of these programs are executed from DOS (before entering Windows) and
allow operation of the IOP-241 in both the DOS and Windows 3.x environments. For optimal
operation, the Client Driver is the preferred method of installation and configuration. The
table below highlights the differences between these programs.
Client Driver (recommended)
File name: IOP241CL.SYS
Enabler
File name: IOP241EN.EXE
File type: DOS executable
File type: DOS device driver
Interfaces to PCMCIA Card and Socket
Services software (PCMCIA host adapter
independent)
Interfaces directly to Intel 82365SL and
other PCIC compatible PCMCIA host
adapters
Allows automatic configuration of IOP-241
adapters upon insertion (Hot Swapping)
Does not support automatic configuration
of IOP-241 adapters upon insertion
(Hot Swapping)
Requires PCMCIA Card and Socket Services
software
Does not require PCMCIA Card and Socket
Services software
Table 1-1. Client Driver versus Enabler
If you are unsure whether Card and Socket Services software is currently installed on your
system, install the IOP-241 Client Driver as discussed in following section. When loaded, the
Client Driver will display an error message if Card and Socket Services software is not
detected.
2.1
IOP-241 Client Driver for DOS
In order to use the IOP-241 Client Driver, the system must be configured with Card and
Socket Services software. (Card and Socket Services software is not provided with the
IOP-241).
IMPORTANT:
Some versions of Card and Socket Services dated before
1993 do not support general purpose I/ O cards. If after
careful installation of the Client Driver, the IOP-241 does
not configure or operate properly, an updated version of
Card and Socket Services software may be required.
IOP-241 Users Manual
10
2.1.1
Client Driver Installation
The following procedure is used to install the IOP-241 Client Driver:
1. Copy the file IOP241CL.SYS from the customer software CD-ROM directory
PCMCIA\ DOS\ CLIENTS onto the root directory of the system hard drive.
2. Using an ASCII text editor, open the system CONFIG.SYS file located in the root
directory of the boot drive.
3. Locate the line(s) in the CONFIG.SYS file where the Card and Socket Services
software is installed.
4. AFTER the line(s) installing the Card and Socket Services software, add the
following to the CONFIG.SYS file: DEVICE = drive:\ path\ IOP241CL.SYS(options),
where options are the IOP-241 Client Driver command line options discussed on the
following pages. (Path is only required if the user places the Client Driver
executable file in a directory other than the root directory).
5. Save the CONFIG.SYS file and exit the text editor.
6. Insert the IOP-241 into one of the system PCMCIA slots.
NOTE: Since the IOP-241 Client Driver supports "Hot Swapping", it is not
necessary to have the IOP-241 installed when booting the system. However, by
inserting the card before booting, the Client Driver will report the card
configuration during the boot process thereby verifying changes made to the
CONFIG.SYS file.
7. Reboot the system and note the message displayed when the IOP-241 Client Driver
is loaded. If the Client Driver reports an "invalid command line option", correct the
entry in the CONFIG.SYS file and reboot the system again. If the Client Driver
reports "Card and Socket Services not found", then Card and Socket Services
software must be installed on the system or the IOP-241 Enabler program must be
used to configure the card. If the Client Driver reports the desired card
configuration, the installation process is complete and the IOP-241 may be removed
and/ or inserted from the system as desired. On each insertion into the PCMCIA
socket, the IOP-241 will be automatically reconfigured according to the command
line options.
IOP-241 Users Manual
11
2.1.2
Command Line Options
The Client Driver accepts up to eight command line arguments from the user to determine the
configuration of the IOP-241. If any arguments are provided, the Client Driver will attempt to
configure the IOP-241 with the options specified in the order they are entered on the
command line. Each argument must be enclosed in parenthesis and must be separated from
other arguments by a space on the command line. Within each argument, any or all of the
following parameters may be specified using a comma (no spaces) to separate each parameter:
b address Specifies the base I/ O address of the IOP-241 in hexadecimal.
“Address” must reside on an even 8-byte boundary (I/ O base address must
end in '0' or '8'). The valid range for the IOP-241’s base address is 100H to 3F8H.
If this option is omitted, a base address is assigned by Card and Socket Services.
i irq
Specifies the interrupt level (IRQ) of the IOP-241 in decimal.
“Irq” must be one of the following values: 3, 4, 5, 7, 9, 10, 11, 12, 14, 15 or 0
if no IRQ is desired. If this option is omitted, an interrupt level will be assigned
by Card and Socket Services.
s socket
Specifies which PCMCIA socket the IOP-241 must be inserted into for
this configuration argument to be used. “Socket” must be in the range of 0 - 15.
If this option is omitted, the configuration argument will apply to cards
inserted into any socket.
2.1.2.1 Example 1
DEVICE = C:\ IOP241CL.SYS
No command line arguments are specified. The Client Driver will configure an IOP-241
inserted into any socket with a base address and IRQ assigned by Card and Socket Services.
2.1.2.2 Example 2
DEVICE = C:\ IOP241CL.SYS (b330)
A single command line argument is provided. The Client Driver will attempt to configure an
IOP-241 inserted into any socket at address 330H and an IRQ assigned by Card and Socket
Services. If address 330H is unavailable, the IOP-241 will not be configured.
2.1.2.3 Example 3
DEVICE = C:\ IOP241CL.SYS (s0,b300,i5)
A single command line argument is provided. The Client Driver will attempt to configure an
IOP-241 inserted into socket 0 with a base address of 300H and IRQ 5. If address 300H or IRQ
5 are unavailable, the IOP-241 will not be configured. In addition, if an IOP-241 is inserted
into any other socket, it will not be configured.
IOP-241 Users Manual
12
2.1.2.4 Example 4
DEVICE = C:\ IOP241CL.SYS (i11,b300)
A single command line argument is provided. Because the parameter order is not significant,
the Client Driver will attempt to configure an IOP-241 inserted into any socket with a base
address of 300H and IRQ 11. If address 300H or IRQ 11 are unavailable, the IOP-241 will not
be configured.
2.1.2.5 Example 5
DEVICE = C:\ IOP241CL.SYS (b300,i5) (i10) ( )
Three command line arguments are provided. The Client Driver will first attempt to
configure an IOP-241 inserted into any socket with a base address of 300H and IRQ5. If
address 300H or IRQ 5 are unavailable, the Client Driver will proceed to the second command
line argument and attempt to configure the card with a base address assigned by Card and
Socket Services and IRQ 10. If IRQ 10 is also unavailable, the Client Driver will proceed to the
third command line argument and attempt to configure the IOP-241 with a base address and
an IRQ assigned by Card and Socket Services.
2.1.2.6 Example 6
DEVICE = C:\ IOP241CL.SYS (b300,i5) ( ) (i10)
In example 6, the three command line arguments of example 5 have been rearranged. The
Client Driver will first attempt to configure an IOP-241 inserted into any socket with a base
address of 300H and IRQ 5. If address 300H or IRQ 5 are unavailable, the Client Driver will
proceed to the second command line argument and attempt to configure the card with a base
address and IRQ assigned by Card and Socket Services. Since the second command line
argument includes all available address and IRQ resources, the third command line argument
will never be reached by the Client Driver. The user must ensure the command line
arguments are placed in a logical order.
2.1.2.7 Example 7
DEVICE = C:\ IOP241CL.SYS (s0,b300,i5) (s1,b340,i10)
The type of configuration shown in example 7 may be desirable in systems where more than
one IOP-241 is to be installed. In this example, the Client Driver will attempt to configure an
IOP-241 inserted into socket 0 with a base address of 300H and IRQ 5. If the IOP-241 is
inserted into socket 1, the Client Driver will attempt to configure it with base address 340H
and IRQ 10. This allows the user to force the IOP-241's address and IRQ settings to be socket
specific which may simplify cable connections and software development. As in the previous
examples, however, if the requested address or interrupt resources are not available, the
IOP-241 will not be configured.
IOP-241 Users Manual
13
2.1.3
Common Problems
2.1.3.1 Generic Client Drivers
Many Card and Socket Services packages include a generic client driver (or SuperClient)
which configures standard I/ O devices. If one of these generic client drivers is installed, it
may configure the IOP-241 causing the client driver to fail installation. In these cases, the user
should do one of the following:
1. Modify the operation of the generic client driver to disable the configuration of
modem/ serial port cards. Consult the Card and Socket Services documentation for
availability and details of this feature.
2. Place the IOP-241 client driver entry before the generic client driver entry in the
system CONFIG.SYS file.
2.1.3.2 Available Resources
One function of the Card and Socket Services software is to track which system resources
(memory addresses, I/ O addresses, IRQs, etc.) are available for assignment to inserted
PCMCIA cards. Sometimes, however, the software assumes or incorrectly determines that a
particular resource is used when it is actually available. Most Card and Socket Services
generate a resource table in a file (typically in the form of an .INI file) which the user can
modify to adjust the available system resources. Consult the Card and Socket Services
documentation for availability and details of this feature.
2.1.3.3 Multiple Configuration Attempts
Some Card and Socket Services have a setting which aborts the configuration process after a
single configuration failure (such as a request for an unavailable resource). The user should
change this setting to allow for multiple configuration attempts. Consult the Card and Socket
Services documentation for availability and details of this feature.
2.1.3.4 Older Versions of Card and Socket Services
Some versions of Card and Socket Services dated before 1993 do not support general purpose
I/ O cards. If after careful installation of the Client Driver the IOP-241 does not configure or
operate properly, an updated version of Card and Socket Services may be required. Card and
Socket Services software is available from Omega.
IOP-241 Users Manual
14
2.2
IOP-241 Enabler for DOS
For systems that are not operating PCMCIA Card and Socket Services software, the IOP-241
DOS Enabler may be used to enable and configure the card. This Enabler, IOP241EN.EXE,
will operate on any DOS system using an Intel 82365SL or PCIC compatible PCMCIA host
adapter including the Cirrus Logic CL-PD6710/ 6720, the VLSI VL82C146 and the Vadem
VG-365.
IMPORTANT:
In order to use the IOP-241 Enabler for DOS, the system
MUST NOT be configured with Card and Socket Services
software. If a Card and Socket Services software is installed,
the IOP-241 Enabler may interfere with its operation and
with the device(s) it controls.
The IOP-241 Enabler does not support automatic configuration of adapters upon insertion,
more commonly referred to as "Hot Swapping". This means the card must be installed in one
of the system's PCMCIA sockets before executing IOP241EN.EXE. If more than one card is
installed in a system, the Enabler must be executed separately for each card. Furthermore,
IOP241EN.EXE should be executed to release the resources used by the card before it is
removed from the PCMCIA socket. Since PCMCIA adapters do not retain their configuration
after removal, any card that is removed from the system must be reconfigured with the
Enabler after re-insertion into a PCMCIA socket.
IMPORTANT:
The Enabler requires a region of high DOS memory when
configuring an IOP-241. This region is 1000H bytes (4KB) long
and by default begins at address D0000H (the default address
may be changed using the "W" option). If a memory manager
such as EMM386, QEMM, or 386Max is installed on the system,
this region of DOS memory must be excluded from the memory
manager's control. Consult the documentation provided with
the memory manager software for instructions on how to
exclude this memory region.
IOP-241 Users Manual
15
2.2.1
Enabler Installation
The following procedure is used to install the IOP-241 Enabler:
1. Copy the file IOP241EN.EXE from the customer software CD-ROM
(directory=PCMCIA\ DOS\ ENABLERS) onto the root directory of the system hard
drive.
2. Using an ASCII text editor, open the system's CONFIG.SYS file located in the root
directory of the boot drive.
3. Locate the line(s) in the CONFIG.SYS file where the Card and Socket Services
software is installed.
4. AFTER the line(s) installing the Card and Socket Services software, add the
following to the CONFIG.SYS file: DEVICE = drive:\ path\ IOP241EN.EXE(options),
where options are the IOP-241 Client Driver command line options discussed on the
following pages. (Path is only required if the Enabler executable file is placed in a
directory other than the root directory).
5. Save the CONFIG.SYS file and exit the text editor.
6. Insert the IOP-241 into one of the system's PCMCIA slots.
NOTE: Since the IOP-241 Enabler does not support "Hot Swapping", it is necessary
to have the IOP-241 installed when booting the system.
7. Reboot the system and note the message displayed when the IOP-241 Enabler is
loaded. If the Enabler reports an "invalid command line option", correct the entry in
the CONFIG.SYS file and reboot the system again. If the Enabler reports the desired
card configuration, the installation process is complete.
IOP-241 Users Manual
16
2.2.2
Command Line Options
To configure an IOP-241, the Enabler requires one command line argument from the user to
determine the configuration of the card. This argument must be enclosed in parenthesis and
within the argument, any or all of the following parameters may be specified using a comma
(no spaces) to separate each parameter:
s socket
Specifies which PCMCIA socket the IOP-241 must be inserted into for
this configuration argument to be used. “Socket” must be in the range of 0 - 15.
This option is always required.
b address Specifies the base I/ O address of the IOP-241 in hexadecimal. “Address”
must reside on an even 8-byte boundary (I/ O base address must end in '0' or '8').
The valid range for the IOP-241’s base address is 100H to 3F8H.
Specify only one of the following options: “b address’ or ‘r’.
Use of one of these options is always required.
i irq
Specifies the interrupt level (IRQ) of the IOP-241 in decimal. “Irq” must be
one of the following values: 3, 4, 5, 7, 9, 10, 11, 12, 14, 15, or 0 if no IRQ is desired.
This option is required if the 'r' option is not used.
w address Specifies the base address of the memory window required to configure
the IOP-241. Set address = D0 for a memory window at segment D000,
address = D8 for a memory window at segment D800, etc. Valid settings
for address are C8, CC, D0, D4, D8 and DC. If this option is omitted, a
memory window at segment D000 will be used.
Before removing an IOP-241 from its PCMCIA socket, the Enabler should be executed to free
the system resources allocated when the card was installed. For this operation the Enabler
provides on additional command line option:
r
Instructs the Client Driver to release the resources previously allocated to the
IOP-241. When the 'r' option is used, any settings specified by the 'b', 'i', 'u' and 'e'
options are ignored. Specify only one of the following options: ‘b address’ or ‘r’.
Use of one of these options is always required.
2.2.2.1 Example 1
DEVICE=C:\ IOP241EN.EXE
No command line argument is specified. The Enabler will report an error and display the
proper usage of the command.
2.2.2.2 Example 2
DEVICE = C:\ IOP241EN.EXE (s0,b300,i5)
The Enabler will configure the IOP-241 in socket 0 with a base address of 300H and IRQ 5
using a configuration memory window at segment D000.
IOP-241 Users Manual
17
2.2.2.3 Example 3
DEVICE = C:\ IOP241EN.EXE (i10,b340,s1)
The Enabler will configure the IOP-241 in socket 1 with a base address of 340H and IRQ 10
using a configuration memory window at segment D000. Note that the parameter order is not
significant.
2.2.2.4 Example 4
DEVICE = C:\ IOP241EN.EXE (s0,b300,i3,wd8)
The Enabler will configure the IOP-241 in socket 0 with a base address of 300H and IRQ 3
using a configuration memory window at segment D800.
2.2.2.5 Example 5
DEVICE = C:\ IOP241EN.EXE (s0,b300,i5,r)
The Enabler will release the configuration used by the IOP-241 in socket 0 using a
configuration memory window at segment D000. The base address and IRQ parameters are
ignored and may be omitted.
2.2.2.6 Example 6
DEVICE = C:\ IOP241EN.EXE (s1,r,wcc)
The Enabler will release the configuration used by the IOP-241 in socket 1 using a
configuration memory window at segment CC00.
2.2.3
Common Problems
2.2.3.1 Memory Range Exclusion
The Enabler requires a region of high DOS memory when configuring an IOP-241. This
region is 1000H bytes (4KB) long and by default begins at address D0000H (the default
address may be changed using the "W" option). If a memory manager such as EMM386,
QEMM or 386Max is installed on the system, this region of DOS memory must be excluded
from the memory manager's control. Consult the documentation provided with the memory
manager software for instructions on how to exclude this memory region.
Furthermore, some systems use the high memory area for BIOS shadowing to improve overall
system performance. In order for the Enabler to operate, any BIOS shadowing must be
disabled in the address range specified for the configuration window. BIOS shadowing can
usually be disabled through the system's CMOS setup utility.
2.2.3.2 Socket Numbers
The Enabler requires the IOP-241's socket number to be specified on the command line and
the IOP-241 must be inserted into the socket before the Enabler is invoked. Some vendors
number their sockets from 1 to N while other vendors number their sockets from 0 to N-1. For
the IOP-241 Enabler, the lowest socket number in the system is designated socket 0.
IOP-241 Users Manual
18
2.2.3.3 Card and Socket Services Software
In order to use the IOP-241 Enabler for DOS, the system MUST NOT be configured with Card
and Socket Services software. If Card and Socket Services software is installed, the IOP-241
Enabler may interfere with its operation and with the device(s) it controls. For systems
configured with Card and Socket Services, the IOP-241 Client Driver is the recommended
method of configuration.
2.3
After Completing Configuration
The IOP-241 is now configured and ready for use. Depending on the type of application
software to be used, the user may wish to review one or more of the following:
1. Chapter 4 of this document provides a basic theory of operation of the card for users
that wish to learn the technical details about the operation of the IOP-241.
2. For users that want to program the IOP-241 with direct I/ O transfers to the card’s
register set, Chapter 5 provides an address map and a detailed description of each
I/ O register.
3. Users that wish to write custom application software without programming the
IOP-241 directly should consult the DAQDRIVE software reference manual.
DAQDRIVE provides a library of data acquisition subroutines and is included free
of charge with the IOP-241.
4. For third party data acquisition software such as LabTech Notebook®, LabVIEW®,
TestPoint® or SnapMaster®, consult the documentation provided by the software
manufacturer.
IOP-241 Users Manual
19
3. Windows 95/98® Installation
To allow easy configuration of the IOP-241, a Windows 95/ 98 "INF" configuration file has
been written for the hardware, (DAQPCARD.INF).
3.1
Installing the IOP-241 Under Windows 95/98
1. Insert the IOP-241 into any available PC Card socket.
2. The first time a new PC Card type is installed the New Hardware Found window
opens. After this first installation Windows 95/ 98 will automatically detect and
configure the card. If the New Hardware Found window does not open, then skip
to the next section, “IOP-241 Resource Settings".
3. The New Hardware Found window provides several options to configure the
IOP-241 card. Click the "Driver from Disk" option button. Click "OK" to continue.
4. An "Install from Disk" dialog box should appear. Insert the customer software
CD-ROM, select the correct drive letter and path for the configuration file
(DAQPCARD.INF) and click "OK". Windows 95/ 98 will browse the path for the
aforementioned file.
The IOP-241 should now be configured. In the future, Windows 95/ 98 will automatically
recognize and configure the IOP-241.
3.2
Resource Settings in Windows 95/98
Windows 95/ 98 maintains a registry of all known hardware installed in the computer. Inside
this hardware registry Windows 95 keeps track of all computer resources, such as base I/ O
addresses, IRQ levels and DMA channels. In the case of a PC Card (PCMCIA), Windows
95/ 98 configures the new hardware using free resources it finds within the hardware registry
and then updates the registry automatically.
To view and/ or edit hardware devices in Windows 95/ 98 use the system Device Manager.
To access Device Manager double click the System icon in the Windows 95/ 98 Control Panel
or click the My Computer icon on the Windows 95/ 98 desktop with the right mouse button
and select Properties from the pull down menu. Consult Windows 95/ 98 on-line help for
details on using the Device Manager.
3.2.1
Viewing Resource Settings with Device Manager
1. Start the Device Manager.
2. Double click on the hardware class Data_Acquisition to list hardware devices in
the class. The IOP-241 belongs to this hardware class. The device name for the
IOP-241 is Omega IOP-241 : PCMCIA Digital I/O Card.
IOP-241 Users Manual
20
3. Open the Properties dialog box for the IOP-241, then click the Resources tab to view
the Input/ Output Range and Interrupt Request resource allocations, (see Figure
3-1).
4. To access the IOP-241, use these system resources allocated by Windows 95/ 98 or
see Changing Resource Settings with Device Manager.
3.3
Changing Resource Settings with Device Manager
1. Start the Windows 95/ 98 Device Manager.
2. Double click on the hardware class Data_Acquisition to list hardware devices in
the class. The IOP-241 belongs to this hardware class. The device name for the
IOP-241 is Omega IOP-241: PCMCIA Digital I/O Card.
3. Open the Properties dialog box for the IOP-241, then click the Resources tab to view
the Input/ Output Range and Interrupt Request resource allocations.
Figure 3-1. Windows 95/ 98 Resource Settings
IOP-241 Users Manual
21
5. To modify either of the resource settings click the resource name and click the
Change Setting button.
6. An Edit Resource window will open. Inside the Edit Resource window click on the
up/ down arrows to the right of the resource value. This scrolls you through all of the
allowable resources for your hardware. Pay attention to the Conflict Information at the
bottom of the window. Do not select a resource that causes a conflict with any other
installed hardware.
7. Repeat the above steps to modify all of the resources allocated to the IOP-241. Once
satisfied with the settings make a note of the new settings and click the OK button to
accept. Clicking the Cancel button does not save your changes.
If any changes have been made to the IOP-241 configuration, the card will automatically be
reconfigured to the new resources specified. Any time a PCMCIA card of this type is inserted,
Windows 95/ 98 will attempt to configure the card at these resource settings. Click the Use
Automatic Settings box to reset this card type for automatic configuration, (see Figure 3-1).
3.4
After Completing Configuration
The IOP-241 is now configured and ready for use. Depending on the type of application
software to be used, the user may wish to review one or more of the following:
1. Chapter 4 of this document provides a basic theory of operation of the card for users
that wish to learn technical details about the operation of the IOP-241.
2. For users that want to program the IOP-241 with direct I/ O transfers to the card’s
register set, Chapter 5 provides an address map and a detailed description of each
I/ O register.
3. Users that wish to write custom application software without programming the
IOP-241 directly should consult the DAQDRIVE software reference manual.
DAQDRIVE provides a library of data acquisition subroutines and is included free
of charge with the IOP-241.
4. For third party data acquisition software such as LabTech Notebook®, LabVIEW®,
TestPoint® or SnapMaster®, consult the documentation provided by the software
manufacturer.
IOP-241 Users Manual
22
4. Theory of Operation
4.1
I/O Port Description
The 24 digital I/ O channels provided by the IOP-241 are grouped into three different ports
with each port containing eight digital I/ O channels. These three ports are controlled via the
Data Port A Control Register, Data Port B Control Register and Data Port C Control Register.
In all three registers, each bit corresponds to one data line. The Data Port A Control Register
is used to access data lines DATA7 - DATA0. The Data Port B Control Register is used to
access data lines DATA15 - DATA8. The Data Port C Control Register is used to access data
lines DATA23 - DATA16.
All of the 24 I/ O channels (DATA23 - DATA0) may be individually programmed for either
input or output. Each data port is latched on a write to that particular port. Each I/ O channel
may be programmed for input by writing a '1' to the appropriate bit in the corresponding data
port control register. The I/ O channels are driven by an open-collector driver, therefore
writing a '1' will turn the open-collector output driver 'off'. When 'off', the open-collector
output driver is tri-stated. Tri-stating the output driver of an I/ O channel will allow that I/ O
channel to be driven by another device. An I/ O channel which is configured for input may be
accessed by reading the appropriate data port control register. If a '0' is written to the
appropriate bit in the corresponding data port control register, the channel may not be used
as input. The channel will be 'masked' and a '0' will always be read on the channel.
If an I/ O channel is to be used as output, the appropriate data port control register should be
written. When a write operation is performed, the data is latched. If a bit is written with a '0',
the open-collector output driver will be turned 'on' and the I/ O channel will be driven to a
low voltage state. Writing a '1' to the appropriate bit will turn the open-collector driver 'off',
but a pull-up resistor will pull the particular I/ O channel to a TTL high voltage level.
Upon reset of the IOP-241, the three data port control registers are all latched with a value of
FFh. This forces all 24 open-collector output drivers 'off' upon a system power-up or upon an
IOP-241 card insertion. Thus, all 24 I/ O channels are configured as input by default. Care
should be taken prior to programming any of these I/ O channels for output. The
open-collector drivers should not be turned 'on' (by writing a '0' to the appropriate bit of a
data port control register) if the I/ O channel is driven by another device. Driving the channel
low by latching a '0' into a bit of the data port control register may cause damage to the
peripheral, the host system or the IOP-241 card if the channel is also being driven by a
peripheral.
IOP-241 Users Manual
23
4.2
Port C Interrupt Description
The eight Port C I/ O channels (DATA23 - DATA16) may also be configured as interrupt
sources. If any of these eight I/ O channels are used to generate an interrupt, the I/ O channel
must be configured for input by latching the appropriate bit in the Data Port C Control
Register to '1'. The interrupt must also be enabled by setting the appropriate bit in the Port C
Interrupt Enable Register. Eight interrupt sources (INT7 - INT0) may be enabled in this
manner; each of these interrupt sources corresponds to an I/ O channel in Port C.
The mode of the port C interrupt sources may be configured in one of four possible manners:
level sensitive active low interrupt, level sensitive active high interrupt, high-to-low transition
edge sensitive interrupt and low-to-high transition edge sensitive interrupt. The lower nibble
(4 bits) and upper nibble (4 bits) of the Port C interrupt sources may be configured separately.
This will allow INT7 - INT4 to be configured for a different mode than INT3 - INT0. These
modes are configured by writing the Interrupt Mode Control Register.
Whenever an interrupt is generated due to a Port C interrupt source, the corresponding bit of
the Interrupt Status Register is set to reflect the cause of the interrupt. This provides a
mechanism for determining the source of a detected interrupt. The Interrupt Status Register
will be continually updated as additional interrupt generating conditions appear.
Writing a '1' to the appropriate bit of the Interrupt Acknowledge Register is the method by
which interrupts should be acknowledged. After a write to the Interrupt Acknowledge
Register, another interrupt will be generated if the Interrupt Status Register does not contain a
value of 00h. Any bit in the Interrupt Status Register which has a value of '1' can be reset to a
value of '0' if the following two conditions are met: first the corresponding bit in the Interrupt
Acknowledge Register must be written with a '1' and second, the interrupt generating
condition must no longer exist. For level sensitive interrupts, an interrupt will be immediately
generated after the write of the Interrupt Acknowledge Register if the interrupt generating
condition (active level on Port C interrupt source) remains.
4.3
External Interrupt Description
In addition to the eight Port C interrupt sources, an additional external interrupt source is
provided in the IOP-241. This external interrupt source is accessed through Pin 29 of the
external connector. The external interrupt source permits the IOP-241 to be operated with
24-bit input/ output and one separate interrupt source.
The Interrupt Mode Control Register provides a means of enabling/ disabling this external
interrupt, setting the external interrupt mode, reading the status of the external interrupt and
acknowledging the external interrupt. The functionality of this external interrupt source is
identical to that described for the Port C interrupt sources in the previous section.
IOP-241 Users Manual
24
5. Register Descriptions
The program registers of the IOP-241 occupy eight adjacent bytes of I/ O address space. These
registers must be programmed to control the operation of the IOP-241. The table below lists
the program registers along with their offsets relative to the I/ O space base address at which
the IOP-241 is located:
Offset
Read/Write
R/ W
R/ W
R/ W
R/ W
R/ W
R
Register
0
1
2
5
6
7
7
Data Port A Control Register
Data Port B Control Register
Data Port C Control Register
Port C Interrupt Enable Register
Interrupt Mode Control Register
Interrupt Status Register
W
Interrupt Acknowledge Register
Table 5-1. IOP-241 Program Registers
Each register of the IOP-241 is discussed in detail in the following sections.
5.1
Data Port A Control Register (Base + 0)
The Data Port A Control Register contains the control bits for I/ O channels DATA0 - DATA7.
Each I/ O channel may be individually programmed for input by writing a '1' to the
appropriate bit of this register.
Bit
7
Name
Description
DATA7
DATA6
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
General Purpose I/ O bit 7
General Purpose I/ O bit 6
General Purpose I/ O bit 5
General Purpose I/ O bit 4
General Purpose I/ O bit 3
General Purpose I/ O bit 2
General Purpose I/ O bit 1
General Purpose I/ O bit 0
6
5
4
3
2
1
0
Table 5-2. Data Port A Control Register
IOP-241 Users Manual
25
5.2
Data Port B Control Register (Base + 1)
The Data Port B Control Register contains the control bits for I/ O channels DATA8 - DATA15.
Each I/ O channel may be individually programmed for input by writing a '1' to the
appropriate bit of this register.
Bit
7
Name
Description
DATA15
DATA14
DATA13
DATA12
DATA11
DATA10
DATA9
DATA8
General Purpose I/ O bit 15
General Purpose I/ O bit 14
General Purpose I/ O bit 13
General Purpose I/ O bit 12
General Purpose I/ O bit 11
General Purpose I/ O bit 10
General Purpose I/ O bit 9
General Purpose I/ O bit 8
6
5
4
3
2
1
0
Table 5-3. Data Port B Control Register
5.3
Data Port C Control Register (Base + 2)
The Data Port C Control Register contains the control bits for I/ O channels DATA16 -
DATA23. Each I/ O channel may be individually programmed for input by writing a '1' to the
appropriate bit of this register. In addition, any of these eight I/ O channels which are
programmed for input may also be used to generate interrupts. In order to program an I/ O
channel as an interrupt source, the Port C Interrupt Enable Register must be set appropriately.
The I/ O channel must also be programmed for input by writing a '1' to the appropriate bit of
the Data Port C Control Register.
Bit
7
Name
Description
DATA23/ INT7
DATA22/ INT6
DATA21/ INT5
DATA20/ INT4
DATA19/ INT3
DATA18/ INT2
DATA17/ INT1
DATA16/ INT0
General Purpose I/ O bit 23 and Interrupt Line 7
General Purpose I/ O bit 22 and Interrupt Line 6
General Purpose I/ O bit 21 and Interrupt Line 5
General Purpose I/ O bit 20 and Interrupt Line 4
General Purpose I/ O bit 19 and Interrupt Line 3
General Purpose I/ O bit 18 and Interrupt Line 2
General Purpose I/ O bit 17 and Interrupt Line 1
General Purpose I/ O bit 16 and Interrupt Line 0
6
5
4
3
2
1
0
Table 5-4. Data Port C Control Register
IOP-241 Users Manual
26
5.4
Port C Interrupt Enable Register (Base + 5)
INT7 - INT0 may be enabled by writing the appropriate bits in the Port C Interrupt Enable
Register. The corresponding I/ O channel must be configured as an input channel via the Data
Port C Control Register if an interrupt is to be generated. If an I/ O channel is configured as
an interrupt source (INT7 - INT0), the I/ O channel continues to be a standard data input
channel (DATA23 - DATA16) and may be read just as any other input signal is read.
Bit
7
Name
Description
INT7EN
INT6EN
INT5EN
INT4EN
INT3EN
INT2EN
INT2EN
INT1EN
1 = Enables INT7; 0 = Disables INT7
1 = Enables INT6; 0 = Disables INT6
1 = Enables INT5; 0 = Disables INT5
1 = Enables INT4; 0 = Disables INT4
1 = Enables INT3; 0 = Disables INT3
1 = Enables INT2; 0 = Disables INT2
1 = Enables INT1; 0 = Disables INT1
1 = Enables INT0; 0 = Disables INT0
6
5
4
3
2
1
0
Table 5-5. Port C Interrupt Control Register
IOP-241 Users Manual
27
5.5
Interrupt Mode Control Register (Base + 6)
The mode of both the external interrupt and the Port C interrupts may be controlled with the
Interrupt Mode Control Register. The upper nibble (4 bits) and lower nibble (4 bits) of the
Port C interrupts may be configured separately. The external interrupt may also be enabled by
writing this register. The status of the external interrupt may be read in this register and the
external interrupt may also be acknowledged by writing the appropriate bit in the Interrupt
Mode Control Register.
Bit
Name
Description
7
ExtIntStat(Read)
ExtIntStat: to read status of external interrupt
ExtIntAck(Write) ExtIntAck: write acknowledges external interrupt
6
ExtraIntEn
1 = external interrupt is enabled
0 = external interrupt is disabled
5:4
ExtIntControl
These two bits control the mode of the external
interrupt:
00 = Level Sensitive Active Low Interrupt
01 = Level Sensitive Active High Interrupt
10 = High-to-low Transition Edge Sensitive Interrupt
11 = Low-to-high Transition Edge Sensitive Interrupt
3:2
1:0
UpperIntCntrl
LowerIntCntrl
These two bits control the mode of the Upper Nibble of
Port C (INT7, INT6, INT5, INT4):
00 = Level Sensitive Active Low Interrupt
01 = Level Sensitive Active High Interrupt
10 = High-to-low Transition Edge Sensitive Interrupt
11 = Low-to-high Transition Edge Sensitive Interrupt
These two bits control the mode of the Lower Nibble of
Port C(INT3, INT2, INT1, INT0):
00 = Level Sensitive Active Low Interrupt
01 = Level Sensitive Active High Interrupt
10 = High-to-low Transition Edge Sensitive Interrupt
11 = Low-to-high Transition Edge Sensitive Interrupt
Table 5-6. Interrupt Mode Control Register
5.6
Interrupt Status Register (Read Only) (Base + 7)
On a read, this register provides the interrupt status for the Port C interrupts. This provides a
mechanism for determining the sources of any pending interrupts. A '1' signals that an
interrupt generating condition has occurred on the appropriate channel. Interrupts will
continue to occur until this register has a value of 00h and no interrupt generating conditions
remain. This register must be 'reset' by acknowledging interrupts via writing the Interrupt
Acknowledge Register.
Bit
Name
Description
7:0
ChanCIntStatus
The Status of INT7 - INT0 is read
(Bit 7 = INT7, Bit 6 = INT6, etc...)
Table 5-7. Interrupt Status Register (Read Only)
IOP-241 Users Manual
28
5.7
Interrupt Acknowledge Register (Write Only) (Base + 7)
Writing a '1' to any bit in the Interrupt Acknowledge Register will acknowledge the interrupt
generating condition which was represented in the corresponding bit of the Interrupt Status
Register. If a '1' is written to a bit in the Interrupt Acknowledge Register and the
corresponding interrupt generating condition is not present, then the appropriate bit in the
Interrupt Status Register will be reset (set to '0').
Bit
Name
Description
7:0
ChanCIntAck
Written to acknowledge INT 7- INT0
(Bit 7 = INT7, Bit 6 = INT6,etc...)
Table 5-8. Interrupt Status Register (Write Only)
5.8
Summary of Interrupt Source Options
Two interrupt source options are provided in the IOP-241 and are summarized below:
(1) Port C Interrupt Sources
(a)
(b)
The following must be programmed:
(i)
Channel set for input via Data Port C Control Register.
(ii)
Interrupt source enabled via Port C Interrupt Enable Register.
(iii) Mode selected via Interrupt Mode Control Register.
Interrupt generated unless Interrupt Status Register is 00h:
(i)
Unacknowledged interrupts are represented by a '1' in the
Interrupt Status Register.
(ii)
Interrupt is generated after write of Interrupt Acknowledge Register
if any interrupts remain unacknowledged.
(c)
'1' in Interrupt Status Register is reset to '0' if the following two requirements are
satisfied:
(i)
Interrupt acknowledged by writing appropriate bit in Interrupt
Acknowledge Register with '1'.
(ii)
Condition which caused interrupt is no longer present.
IOP-241 Users Manual
29
(2)
External Interrupt Source
(a)
The following must be programmed:
(i)
(ii)
Interrupt source enabled via Interrupt Mode Control Register.
Mode selected via Interrupt Mode Control Register.
(b)
(c)
Interrupt generated if ExtIntStat of Interrupt Mode Control Register is '1'.
'1' in ExtIntStatus is reset to '0' if the following two requirements are satisfied:
(i)
(ii)
Interrupt acknowledged by writing ExtIntAck with '1'.
Condition which caused interrupt is no longer present.
5.9
Summary of Input/Output Options
Each of the three ports (Port A, Port B, Port C) may be configured in one of three manners:
(1)
PORT USED AS AN OUTPUT
(a)
(b)
Write a '1' to the appropriate bits of the latch in order to turn 'off' the output
module.
Write a '0' to the appropriate bits of the latch in order to turn 'on' the output
module.
(2)
(3)
PORT USED AS AN INPUT
(a)
Writing a '1' to all the bits of the latch will allow all the channels of the port to be
read as inputs. (Writing a '0' to any bits of the latch will 'mask' those bits. Those
bits will always be read as a '0').
PORT USED AS INPUT AND OUTPUT
If a port is to be used so that some channels are inputs and some channels are outputs, it must
be insured that the channels to be used as inputs are initialized as inputs. This is done by
writing a '1' to the bits of the data port control register representing the I/ O channels which
are to be used as inputs anytime the port is written.
(a)
(b)
(c)
The channels which are to be inputs should always be written with a '1' and
never written with a '0'.
The channels which are to be outputs should be written with the appropriate
value ('0' or '1').
The channels which are latched with a '0' will always be '0' when read (they are
'masked' from input).
IOP-241 Users Manual
30
5.10
Programming Example
The following C program segment demonstrates how to program an IOP-241 located at I/ O
base address 300h. Port A will be programmed as output, and 55h will be latched at Port A.
Port B will be configured with it's upper 3 bits as output and it's lower five bits as input. The
upper three bits will be latched with 010b. Port C will be configured as input. Interrupts will
be enabled as explained in the program comments.
outp(0x300,0x55);
outp(0x301,0x5F);
/ * writes 55h to Port A */
/ * writes 010b to Port B upper 3 bits*/
/ * sets Port B lower 5 bits for input */
outp(0x302,0xFF);
/ * initializes Port C for input */
Port_B = inp(0x301); / * reads data from Port B */
/ * Port_B(bit7) = '0' and Port_B(bit5) = '0' due to 'masking' */
Port_C = inp(0x302); / * reads data from Port C */
outp(0x306,0x76);
/ * INT7 - INT4 set for Level Sensitive Active High Interrupt Mode */
/ * INT3 - INT0 set for Edge Sensitive High-to-low Transition Interrupt Source */
/ * External Interrupt Source Enabled */
/ * External Interrupt Source set for Low-to-high Edge Sensitive Interrupt Source*/
outp(0x305,0x77);
/ * Enables six Port C interrupt sources */
/ * Enables INT6,INT5,INT4,INT2,INT1,INT0 */
IOP-241 Users Manual
31
6. External Connections
The IOP-241 is fitted with a 33-pin 0.8mm shielded connector with the pins assigned as shown
in Figure 6-1 below.
1
GND
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
GND
5
10
15
20
25
DATA8
DATA9
DATA10
DATA11
DATA12
DATA13
DATA14
DATA15
GND
DATA16/ INT0
DATA17/ INT1
DATA18/ INT2
DATA19/ INT3
DATA20/ INT4
DATA21/ INT5
DATA22/ INT6
DATA23/ INT7
GND
EXT_IRQ
30
33
GND
GND
GND
GND
Figure 6-1. IOP-241 33-Pin Connector
IOP-241 Users Manual
32
7. Optional Accessories
7.1 CP-1037 Cable Assembly
An optional cable assembly, Omega product number CP-1037, is available to convert the
IOP-241's 33-pin 0.8mm I/ O connector to a standard D-37 male connector. The first 31
connections on the IOP-241 map directly to the first 31 pins of the D37 connector. Note that
two of the IOP-241 ground connections (pins 32 and 33) are not available when using the
CP-1037. Figure 7-1 illustrates the D37 connector pin assignments.
19
GND
37
N/ C
18
DATA15
36
N/ C
17
DATA14
35
N/ C
16
DATA13
34
N/ C
15
DATA12
33
N/ C
14
13
12
11
10
9
DATA11
32
31
30
29
28
27
26
25
24
23
22
21
20
N/ C
DATA10
DATA9
DATA8
GND
GND
GND
EXT_IRQ
GND
DATA7
DATA6
DATA23/ INT7
DATA22/ INT6
DATA21/ INT5
DATA20/ INT4
DATA19/ INT3
DATA18/ INT2
DATA17/ INT1
DATA16/ INT0
8
7
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
GND
6
5
4
3
2
1
Figure 7-1. CP-1037 D37 Pin Assignments
IOP-241 Users Manual
33
7.2 UIO-37 Screw Terminal Block
The UIO-37 Screw Terminal Block shown in Figure 7-2 connects directly to the optional
CP-1037 cable assembly to provide users with a screw terminal interface. The D37 connector of
the CP-1037 connects directly to the 37 screw terminal blocks of the UIO-37. Each screw
terminal is numbered for easy reference.
NOTE:
Since only the first 31 connections on the IOP-241 are available on the CP-1037 cable assembly,
two of the IOP-241's ground connections (pins 32 and 33) are not available when using the
UIO-37.
Figure 7-2. UIO-37 Screw Terminal Block
IOP-241 Users Manual
34
8. Specifications
Bus Interface
Physical Dimensions
PCMCIA PC Card Standard 2.1 compliant
Type II PCMCIA card (5mm)
Power Requirements
Digital Input/Output
+5 volts 7.33 mA Typical (all outputs 'off')
12.38 mA Maximum (all outputs 'off')
36.38 mA Maximum (all outputs 'on')
TTL Compatible
Current Source/Sink
Sink 6mA(min) at 0.33V
(at 25° C)
Sink 20mA(max) at 1.0V
Source 1.1mA (max) into 0Ω at Vcc = 5V
Input/Output Current
Connector
25mA Maximum
Adapter to standard male D37
IOP-241 Users Manual
35
IOP-241 Users Manual
Version 2.30
January 25, 1999
Part No. 940-0077-230
IOP-241 Users Manual
36
|